1-5/16" Diameter x 3/16" Thick, Series 2, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

3/8" Diameter x 3/32" Thick, Series Y, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

3/8" Diameter x 3/32" Thick, Series Y, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

13/32" Diameter x 3/32" Thick, Series Y, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

13/32" Diameter x 3/32" Thick, Series Y, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

7/16" Diameter x 3/32" Thick, Series Y, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

7/16" Diameter x 3/32" Thick, Series Y, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

15/32" Diameter x 3/32" Thick, Series Z, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

1-11/32" Diameter x 3/16" Thick, Series 2, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

15/32" Diameter x 3/32" Thick, Series Z, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

1/2" Diameter x 3/32" Thick, Series Z, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

1/2" Diameter x 3/32" Thick, Series Z, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

17/32" Diameter x 1/8" Thick, Series 0, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

1-3/8" Diameter x 3/16" Thick, Series 2, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree

17/32" Diameter x 1/8" Thick, Series 0, Flat Bottom Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4For general use in carbon steel, steel alloys, stainless steel, cast iron, aluminum and non-ferrous Point Angle  - 180 degree