35/64" Diameter x 1/8" Thick, Series 0, SV-Point Super Cobalt (T15) Spade Drill Insert H Coated

Sinusoidal thinning edge for smooth cutting Positive rake angleFor use in high nickel alloys materials over 280 Brinell Performs best in rigid setups Point Angle  - 132 degree, (Series 5-8 :...

12mm Diameter x 2.4mm Thick, Series Z, SV-Point Super Cobalt (T15) Spade Drill Insert H Coated

Sinusoidal thinning edge for smooth cutting Positive rake angleFor use in high nickel alloys materials over 280 Brinell Performs best in rigid setups Point Angle  - 132 degree, (Series 5-8 :...

10mm Diameter x 2.4mm Thick, Series Y, SV-Point Super Cobalt (T15) Spade Drill Insert H Coated

Sinusoidal thinning edge for smooth cutting Positive rake angleFor use in high nickel alloys materials over 280 Brinell Performs best in rigid setups Point Angle  - 132 degree, (Series 5-8 :...

1/2" Dia., 3 Flute., 2" LOC, 0.060" Corner Rad, ALU-Power HPC Chipbreaker DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/8" Dia., 3 Flute., 1" LOC, 0.030" Corner Rad, ALU-Power HPC Chipbreaker DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

1" Dia., 3 Flute., 1-1/4" LOC, 2-5/8" Reach, 5" OAL, 0.090" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

3/4" Dia., 3 Flute., 1" LOC, 2" Reach, 4" OAL, 0.060" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

5/8" Dia., 3 Flute., 3/4" LOC, 1-5/8" Reach, 4" OAL, 0.060" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

1/2" Dia., 3 Flute., 5/8" LOC, 3-3/8" Reach, 5" OAL, 0.030" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/4" Dia., 3 Flute., 1" LOC, 3-3/8" Reach, 6" OAL, 0.010" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

3/4" Dia., 3 Flute., 1" LOC, 2" Reach, 4" OAL, 0.010" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

1/2 Dia., 3 Flute., 5/8 LOC, 1-3/8 Reach, 3 OAL, ALU-Power HPC DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

1/8" Dia., 3 Flute., 1/4" LOC, 0.030" Corner Rad, ALU-Power HPC DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

5/8" Dia., 3 Flute., 3" LOC, 0.010" Corner Rad, ALU-Power HPC DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...

3/8" Dia., 3 Flute., 1-1/2" LOC, 0.010" Corner Rad, ALU-Power HPC DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.More efficient chip evacuation.Ability to counteract extreme radial forces.DLC Coated Provides...