3/4" Diameter x 5/32" Thick, Series 1, Super Cobalt (T15) Spade Drill Insert Hardslick Coated

Increase wear resistance over M4 For use in medium carbon steel to high temperature alloys Performs best in rigid setups Point Angle  - 132 degree, (Series 5-8 : 144 degree)

3/4" Diameter x 5/32" Thick, Series 1, Super Cobalt (T15) Spade Drill Insert TiAlN Coated

Increase wear resistance over M4 For use in medium carbon steel to high temperature Performs best in rigid setups Point Angle  - 132 degree, (Series 5-8 : 144 degree)

3/4" Diameter x 5/32" Thick, Series 1, Super Cobalt (T15) Spade Drill Insert TiN Coated

Increase wear resistance over M4 For use in medium carbon steel to high temperature Performs best in rigid setups Point Angle  - 132 degree, (Series 5-8 : 144 degree)

3/4" Diameter x 5/32" Thick, Series 1, HSS (M4) Spade Drill Insert Hardslick Coated

General purpose insert for most materials Not recommended for tool steels and high temperature alloys High toughness for loose or manual machines Point Angle  - 132 degree, (Series 5-8 : 144...

3/4" Diameter x 5/32" Thick, Series 1, HSS (M4) Spade Drill Insert TiAlN Coated

General purpose insert for most materials Not recommended for tool steels and high temperature alloys High toughness for loose or manual machines Point Angle  - 132 degree, (Series 5-8 : 144...

3/4" Diameter x 5/32" Thick, Series 1, HSS (M4) Spade Drill Insert TiN Coated

General purpose insert for most materials Not recommended for tool steels and high temperature alloys High toughness for loose or manual machines Point Angle  - 132 degree, (Series 5-8 : 144...

3/4" Dia., 3 Flute., 1" LOC, 5" Reach, 7" OAL, 0.060" Corner Rad, ALU-Power Uncoated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/4" Dia., 3 Flute, 1" LOC, 2" Reach, 4" OAL, 0.030" Corner Rad, ALU-Power Uncoated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/8" Dia., 3 Flute., 1/2" LOC, 0.010" Corner Rad, ALU-Power HPC Chipbreaker DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/4" Dia., 3 Flute., 1" LOC, 5" Reach, 7" OAL, 0.060" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/4" Dia., 3 Flute., 1" LOC, 2" Reach, 4" OAL, 0.030" Corner Rad, ALU-Power DLC Coated Carbide End Mill

  Balanced cutting with less vibration.Ability to run at high speeds with less heat in aluminum.Chip Breaker Improves chip evacuation by shortening the chip length.Ability to counteract extreme...

3/8" Long Length i-Smart Carbide Holder, Straight Neck, For Modular Milling Heads, 3/8" Shank, M6 Thread

ZMC Series: i-Smart Carbide Holders, Straight Neck Type For Screw On Modular Milling Heads Reduce Cost as Compared to Solid Carbide End Mills Coolant Hole Through The Shank Wrench Included With Each...

3/8 Dia., 4 Flute., 7/8 LOC, Flat Shank, V7 Plus A, Coated Carbide End Mill

V7PlusA For Stainless Steels, Mild Steels, Cast Iron, Low/Medium Hardness Materials Under Hrc40  Excellent material removal rates and surface finishes Unequal indexing for reduced chatter...

3/8" Dia., 6 Flute., 5/8" LOC, 0.030" Corner Rad, Chip Splitter V7 Plus A, Coated Carbide End Mill

V7PlusA For Stainless Steels, Mild Steels, Cast Iron, Low/Medium Hardness Materials Under Hrc40  Excellent material removal rates and surface finishes Unequal indexing for reduced chatter...

3/8" Dia., 6 Flute., 5/8" LOC, V7 Plus A, Coated Carbide End Mill

V7PlusA For Stainless Steels, Mild Steels, Cast Iron, Low/Medium Hardness Materials Under Hrc40  Excellent material removal rates and surface finishes Unequal indexing for reduced chatter...